Hypercube Evolution 3D Printer: Unterschied zwischen den Versionen

Aus ProjectWiki
Wechseln zu:Navigation, Suche
(Die Seite wurde neu angelegt: „== Parts overview == frameless|Parts overview == Frame == frameless|Frame == Dampened Feet ==…“)
 
K (Housing)
 
(4 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt)
Zeile 7: Zeile 7:
 
== Dampened Feet ==
 
== Dampened Feet ==
 
To mount the damper feets, the extrusions need to be tapped. Because the standard 3-flute hand tap does not bite in the first few millimeters, I improvised a 1-flute tap to start the thread and finished it with the 3-flute tap.
 
To mount the damper feets, the extrusions need to be tapped. Because the standard 3-flute hand tap does not bite in the first few millimeters, I improvised a 1-flute tap to start the thread and finished it with the 3-flute tap.
 +
 
[[Datei:Hevo improvised tap.jpg|frameless|Improvised tap]]
 
[[Datei:Hevo improvised tap.jpg|frameless|Improvised tap]]
 
[[Datei:Hevo improvised tap 2.jpg|frameless|Improvised tap closeup]]
 
[[Datei:Hevo improvised tap 2.jpg|frameless|Improvised tap closeup]]
Zeile 13: Zeile 14:
  
 
== Housing ==
 
== Housing ==
 +
Machining the MDF back-, cover- and base plates
 +
 
[[Datei:Hevo mdf machined.jpg|frameless|MDF plates after machining]]
 
[[Datei:Hevo mdf machined.jpg|frameless|MDF plates after machining]]
 +
[[Datei:Backplate_milling_cable_ducts.jpg|frameless|Milling the cable ducts]]
 +
[[Datei:Backplate_milled_cable_ducts.jpg|frameless|Finished cable ducts]]
 +
 
[[Datei:Hevo frame housing.jpg|frameless|Housing plates mounted on the frame]]
 
[[Datei:Hevo frame housing.jpg|frameless|Housing plates mounted on the frame]]
 +
 +
== Bed assembly ==
 +
[[Datei:Hevo bed frame.jpg|frameless|Bed frame assembled]]
 +
[[Datei:Bed_cablechain.jpg|frameless|Cable chain attached]]
 +
 +
 +
[[Datei:Bed_plate_drilled.jpg|frameless|Machined holes in naked aluminium bed plate]]
 +
[[Datei:Bed_screw_and_spring.jpg|frameless|Screws and silicone springs mounted]]
 +
[[Datei:Bed_heater_thermal_fuse_applied.jpg|frameless|Applied the 230V/800W heating mat and a manually resettable thermal fuse]]
 +
[[Datei:Applying_bed_layers.jpg|frameless|Applying the adhesives to the flex printing surface]]
 +
 +
[[Datei:Bed_flex_plate_positioning_brackets.jpg|frameless|Print surface positioning brackets cut from aluminium L-beams]]
 +
[[Datei:Bed_flex_plate_positioning_brackets_mounted.jpg|frameless|Positioning brackets mounted]]
 +
[[Datei:Bed_print_surface_fr4.jpg|frameless|FR4 print surface]]
 +
 +
 +
To hold the insulation material beneath the bed in place, I've made this support plate:
 +
 +
[[Datei:Bed_insulation_material_support.jpg|frameless|Cutted beams and drilled support plate]]
 +
[[Datei:Bed_insulation_support_top.jpg|frameless|Support plate sitting on top of the bed frame]]
 +
[[Datei:Bed_insulation_support_bottom.jpg|frameless|Support plate seen from below]]
 +
[[Datei:Bed_insulation.jpg|frameless|Bed insulation material, the sides are covered in tape to prevent fluff]]
 +
 +
 +
[[Datei:Bed_completed_assembly.jpg|frameless|Bed assembly completed]]
 +
  
 
== Z-Axis ==
 
== Z-Axis ==
[[Datei:Hevo bed frame.jpg|frameless|Bed frame assembled]]
 
 
[[Datei:Hevo z linear guides.jpg|frameless|Z linear guides and bed frame mounted]]
 
[[Datei:Hevo z linear guides.jpg|frameless|Z linear guides and bed frame mounted]]
 +
[[Datei:Z_linear_screw.jpg|frameless|Z axis linear screws mounted]]
 +
 +
 +
== X-, Y-Axis ==
 +
[[Datei:Linear_rails.jpg|frameless|Linear rails cleaned, greased and ready to be mounted]]
 +
[[Datei:Linear_rails_detail.jpg|frameless|Applied some screw lock]]
 +
 +
 +
[[Datei:Y_carriage_on_rail.jpg|frameless|Y carriage on the rail]]
 +
[[Datei:Y_optical_endstop.jpg|frameless|Optical end stop on the Y-axis]]
 +
 +
 +
[[Datei:X_carriage_front.jpg|frameless|X carriage and hot end front view]]
 +
[[Datei:X_carriage_below.jpg|frameless|X carriage and hot end from below]]
 +
 +
 +
[[Datei:Belt_idler.jpg|frameless|Belt idler mounted]]

Aktuelle Version vom 17. Mai 2021, 21:10 Uhr

Parts overview

Parts overview

Frame

Frame

Dampened Feet

To mount the damper feets, the extrusions need to be tapped. Because the standard 3-flute hand tap does not bite in the first few millimeters, I improvised a 1-flute tap to start the thread and finished it with the 3-flute tap.

Improvised tap Improvised tap closeup

Dampened feet

Housing

Machining the MDF back-, cover- and base plates

MDF plates after machining Milling the cable ducts Finished cable ducts

Housing plates mounted on the frame

Bed assembly

Bed frame assembled Cable chain attached


Machined holes in naked aluminium bed plate Screws and silicone springs mounted Applied the 230V/800W heating mat and a manually resettable thermal fuse Applying the adhesives to the flex printing surface

Print surface positioning brackets cut from aluminium L-beams Positioning brackets mounted FR4 print surface


To hold the insulation material beneath the bed in place, I've made this support plate:

Cutted beams and drilled support plate Support plate sitting on top of the bed frame Support plate seen from below Bed insulation material, the sides are covered in tape to prevent fluff


Bed assembly completed


Z-Axis

Z linear guides and bed frame mounted Z axis linear screws mounted


X-, Y-Axis

Linear rails cleaned, greased and ready to be mounted Applied some screw lock


Y carriage on the rail Optical end stop on the Y-axis


X carriage and hot end front view X carriage and hot end from below


Belt idler mounted